[+] expand

Foot Controller Soft Case

Model: 1SKB-SC2111

The SKB-SC2111 Controller Soft Case is designed to fit all-in-one effects floor boards (BOSS GT-10, Digitech RP1000, Line6 X3 Live, Vox Tonelab LE and many more) as well as MIDI foot controllers (Roland FC300, etc.)A rigid EPS...

Interior Length: 21.50 in (54.61 cm)
Interior Width: 11.25 in (28.58 cm)
Interior Depth: 4.00 in (10.16 cm)
The SKB-SC2111 Controller Soft Case is designed to fit all-in-one effects floor boards (BOSS GT-10, Digitech RP1000, Line6 X3 Live, Vox Tonelab LE and many more) as well as MIDI foot controllers (Roland FC300, etc.)

A rigid EPS foam interior is surrounded by a heavy-duty canvas exterior with an exterior zippered pocket. A removable one inch (1”) pad of convoluted foam in the lid is provided to allow for various product heights. A shoulder strap and padded carrying handle is also included to make transport simple. Backed by SKB's 2 year Soft Product Warranty.

Features
  • Heavy duty double pull zipper
  • Durable 600 Denier exterior layered with rigid foam
  • Padded interior
  • Convenient exterior accessory pouch
  • Carrying handle and convenient shoulder strap
  • Backed by SKB's 2 year Soft Product Warranty
Specifications
Interior Length
21.50 in
54.61 cm
Interior Width
11.25 in
28.58 cm
Interior Depth
4.00 in
10.16 cm
Exterior Length
23.75 in
60.33 cm
Exterior Width
14.50 in
36.83 cm
Exterior Depth
5.75 in
14.61 cm
Carton Length
26.50 in
67.31 cm
Carton Width
15.50 in
39.37 cm
Carton Depth
6.50 in
16.51 cm
Shipping Weight
5.20 lb
2.36 kg
Product Weight
3.60 lb
1.63 kg

Interior height is measured with max foam compression. Without foam the internal height is 6".
Soft Product Warranty

SKB Soft Products are fully warranted to the original owner against defects in materials and craftsmanship for one year from purchase. Any defects in workmanship will be covered by SKB. Damages due to accident, improper care, negligence or normal wear, where SKB is not at fault, are not covered on Soft Products. Freight cost to SKB Corporation is the responsibility of the customer. SKB will pay the return freight for warranty product shipped back to the customer.

How do I know which D/C polarity my pedals need?
Most effects pedals are marked somewhere on the pedal (either near the power connector or on the bottom of the pedal). It might also be mentioned in the owner's manual. Otherwise, you should check the website of the manufacturer or contact the manafacturer of the pedal you are wondering about. The polarity switch on the PS-55 represents "center" polarity (the polarity at the center of the plug)

On the PS-45, how do you connect pedals for the front of my preamp AND the effects loop?
The following information is based on looking at the PS-45 from the "performance" position with the audio connections in front of you on the right side of the PS-45. To further illustrate the point of reference, the "Bottom row" (as it is called in the following information) is represented by an audio jack on the far right labeled "To Pedal." The "Top Row" (as it is called in the following information) is represented by an audio jack on the far right labeled "From Guitar." The ">" basically represents a connection (patch/audio cable). Here’s how you do it: Bottom row config: To Pedal > input of 1st pedal that belongs in front of the preamp* > daisy chain through remaining pedals that belong in front of preamp > output of last pedal that belongs in front of the preamp> From pedal (bottom) > Left/Mono > amp input... Top row config: guitar > From Guitar. Output of last pedal that belongs in amp fx loop > From Pedal (top) > PS-45 Send > amp fx loop return > amp fx loop send > PS-45 Return > Right (To Amplifier Input) > input of 1st pedal that belongs in amp fx loop... *preamp represents the place you plug into on the front of your amp. Some people have rack gear that has a separate preamp and power amp. With a standard amp head or combo amp, you plug into the amp’s input and you are introducing the signal to the preamp. When you plug into the return of the effects loop, you are introducing the signal to the power amp section of your amp.

On the PS-55, I tried to run my amp's footswitch through the board, but it doesn't function properly in that configuration?
Configuration 3 & 4 in the manual show an amp footswitch connected through the PS-55. This is based on a number of amp footswitches that use a T/S (Tip/Sleeve)1/4" cable to connect to the amp. if your amp's footswitch is T/R/S (Tip/Ring/Sleeve) or a proprietary cable, these configurations will not work.

On the PS-55, the cable tester and headphone amp work, but my pedals don't power on?
It is important to make sure that the proper polarity has been selected on each D/C output for the pedal it is attached to. Most pedals are "center negative" type pedals and if you have the output set to positive, these pedals won't power up.

On the PS-55, what are the DC output current ratings?
ALL of the DC outputs on the PS-55 are 100mA. There are two 9VAC outputs that are rated at 1.3A (1300mA), however, every DC output is rated at 100mA (9VDC, 12VDC, 18VDC, 24VDC and the two variable DC outputs). All outputs have their own winding on the transformer and are isolated.

On the PS-55, what is the purpose of the Guitar Buffer Preamp?
Some guitarists like to use long cables between their guitar and the pedalboard so they can move around more on the stage. The problem with long cables is the drop in gain. The Guitar Buffer Preamp allows you to get that gain back and have it BEFORE your guitar signal gets to the pedals. Another way to use it is when you have two guitars that you like to use and one guitar has a hotter output than the other one. Usually, when you switch guitars, you have to make a bunch of setting adjustments on your pedals to compensate for the weaker guitar (and adjust the pedals again when you switch back to the hotter guitar). Instead, plug the hotter guitar into the Guitar Buffer preamp bypass and adjust all of your pedals the way you like them. Now, when you switch to the weaker guitar, unplug from the Bypass and plug into the Guitar Buffer Preamp and bring the gain up to match the hotter guitar. This way, you don’t have to keep adjusting all of your pedals every time you want to switch guitars!

What cables are included with the PS-55?
A power cable for connecting the PS-55 to a wall outlet and an assortment of output power cables. No audio cables are supplied (mainly because most guitarists like to use their favorite brand of cable. We do include a cable tester for people that like to build their own cables)

What type of power supply comes with the PS-15 pedalboard?
The pedalboards come with a 120 V AC 9V DC 500 m/amps regulated power adaptor with a negative tip.

Which pedal goes first (what is the "order" for connecting pedals?)
The closest thing to a "standard" is that the tone based pedals (wah, EQ, overdrive, etc.) should go in front of the Preamp and time based pedals (delay, reverb, chorus, etc.) after the Preamp (in the effects loop). This is not the law, but a rule-of-thumb. There is a helpful article from Boss at the URL: http://media.bossus.com/bugonline/how_to.asp?art=order

Why isn't there any A/C outlets on the PS-55 like there are on the PS-45?
The PS-55 is a pedalboard designed to be used all over the world, so it includes a dual voltage feature (115/230VAC) so you can plug it in anywhere. While the extra A/C outlets might have been useful for someone in the U.S., a guitarist in the U.K., Germany or Japan would see it as a waste. Since you have to get A/C power out to the PS-55 anyway, use a powerstrip for the one or two pedals that you might need outlets for and run the rest off of the PS-55. While it might not be the most convenient way to go, it will certainly work. The PS-45 is only sold in the U.S.