Added To Cart
Model: 3i-1813-7WMC
The 3i-1813-7WMC Wireless Mic case is part of the Waterproof Series of cases with a custom foam interior to protect a variety of brands including Shure and Sennheiser mics to name a few.
Read More
The 3i-1813-7WMC Wireless Mic case is part of the Waterproof Series of cases with a custom foam interior to protect a variety of brands including Shure and Sennheiser mics to name a few.
This dual layer custom foam interior is designed to cradle each mic and will fit up to eight handheld wireless microphones, eight wireless body pack transmitters and accessories. Convenient finger holes to quickly grab the microphone and easily slide in the body pack transmitters on their side to protect the antenna. An open pocket is perfect to hold mic clips, batteries and other accessories.
SKB iSeries Injection Molded Mil-Standard Waterproof Cases are molded of ultra high-strength polypropylene copolymer resin, featuring a gasket-sealed, water and dust tight, submersible design (MIL-STD 810G) that is resistant to corrosion and impact damage. Standard features include a molded-in hinge, padlock loops, patented trigger release latches, snap-down rubber over-molded cushion grip handle, automatic ambient pressure equalization valve (MIL-STD 810G), and resistance to UV, solvents, corrosion, fungus and impact damage (MIL-STD 810G).
Prop65 Information
This product can expose you to chemicals including chloroprene, which is known to the State of California to cause cancer. For more information go to p65warnings.ca.gov
- Custom dual layer foam interior to hold eight wireless mics, body packs and accessories
- Convenient finger slots for easy access
- Ultra high-strength polypropylene copolymer resin
- UV, solvent, corrosion and fungus resistant (MIL-STD 810G)
- Complete gasket seal makes these cases absolutely watertight (MIL-STD 810G)
- Automatic ambient pressure equalization value (MIL-STD 810G)
- Resistant to corrosion and impact damage
- Molded-in hinges
- Trigger release latch system
- Rubber over-molded cushion grip handle
Exterior
Hard
Product Weight
9.7 lb
4.40 kg
Exterior Length
19.875 in
50.48 cm
Exterior Width
15.5 in
39.37 cm
Exterior Height
7.875 in
20.00 cm
Carton Length
20 in
50.80 cm
Carton Width
16 in
40.64 cm
Carton Height
8 in
20.32 cm
Shipping Weight
10.88 lb
4.93 kg
SKB-branded hardshell cases are fully warranted against defects in materials and craftsmanship for the life of the case to the original owner. That means if your case breaks, SKB will supply replacement parts, repair the case, or replace your case for as long as you own it. Proof of Purchase is required for all warranty claims. SKB is not responsible for the shipping cost to our facility. However, SKB will cover all of the costs of repairs and/or replacements, as well as the return shipping. To request a return authorization for a warranty claim or field replaceable parts, please contact our customer service department through our online Support Request form. SKB-branded hardshell cases are warranted for life to the original owner only. Cases that have been modified, previously owned, or used for rental purposes by institutions or schools are not covered by this warranty.
Chart of all SKB iSeries products and its dimensions.
Yes. Minimum quantities are required. Submit a quote request here.
SKB-branded hardshell cases are fully warranted against defects in materials and craftsmanship for the life of the case to the original owner. That means if your case breaks, SKB will supply replacement parts, repair the case, or replace your case for as long as you own it. Proof of Purchase is required for all warranty claims. To register your case, fill out the form here.
Most latches, handles, and wheels are considered field replaceable, and can be provided at no charge to the original owner. If you need parts, contact our customer service department:
By phone: (714) 685-5207
By email: customerservice@skbcases.com
Online: Support Request form
Most repairs can be completed within two weeks of receiving your case.
Some cases can be retrofitted with TSA latches. Please contact our customer service department at (714) 685-5207 or customerservice@skbcases.com for more information.
Model: 3i-1813-7WMC
The 3i-1813-7WMC Wireless Mic case is part of the Waterproof Series of cases with a custom foam interior to protect a variety of brands including Shure and Sennheiser mics to name a few.
Read More
The 3i-1813-7WMC Wireless Mic case is part of the Waterproof Series of cases with a custom foam interior to protect a variety of brands including Shure and Sennheiser mics to name a few.
This dual layer custom foam interior is designed to cradle each mic and will fit up to eight handheld wireless microphones, eight wireless body pack transmitters and accessories. Convenient finger holes to quickly grab the microphone and easily slide in the body pack transmitters on their side to protect the antenna. An open pocket is perfect to hold mic clips, batteries and other accessories.
SKB iSeries Injection Molded Mil-Standard Waterproof Cases are molded of ultra high-strength polypropylene copolymer resin, featuring a gasket-sealed, water and dust tight, submersible design (MIL-STD 810G) that is resistant to corrosion and impact damage. Standard features include a molded-in hinge, padlock loops, patented trigger release latches, snap-down rubber over-molded cushion grip handle, automatic ambient pressure equalization valve (MIL-STD 810G), and resistance to UV, solvents, corrosion, fungus and impact damage (MIL-STD 810G).
Prop65 Information
This product can expose you to chemicals including chloroprene, which is known to the State of California to cause cancer. For more information go to p65warnings.ca.gov
- Custom dual layer foam interior to hold eight wireless mics, body packs and accessories
- Convenient finger slots for easy access
- Ultra high-strength polypropylene copolymer resin
- UV, solvent, corrosion and fungus resistant (MIL-STD 810G)
- Complete gasket seal makes these cases absolutely watertight (MIL-STD 810G)
- Automatic ambient pressure equalization value (MIL-STD 810G)
- Resistant to corrosion and impact damage
- Molded-in hinges
- Trigger release latch system
- Rubber over-molded cushion grip handle
Exterior
Hard
Product Weight
9.7 lb
4.40 kg
Exterior Length
19.875 in
50.48 cm
Exterior Width
15.5 in
39.37 cm
Exterior Height
7.875 in
20.00 cm
Carton Length
20 in
50.80 cm
Carton Width
16 in
40.64 cm
Carton Height
8 in
20.32 cm
Shipping Weight
10.88 lb
4.93 kg
SKB-branded hardshell cases are fully warranted against defects in materials and craftsmanship for the life of the case to the original owner. That means if your case breaks, SKB will supply replacement parts, repair the case, or replace your case for as long as you own it. Proof of Purchase is required for all warranty claims. SKB is not responsible for the shipping cost to our facility. However, SKB will cover all of the costs of repairs and/or replacements, as well as the return shipping. To request a return authorization for a warranty claim or field replaceable parts, please contact our customer service department through our online Support Request form. SKB-branded hardshell cases are warranted for life to the original owner only. Cases that have been modified, previously owned, or used for rental purposes by institutions or schools are not covered by this warranty.
Chart of all SKB iSeries products and its dimensions.
Yes. Minimum quantities are required. Submit a quote request here.
SKB-branded hardshell cases are fully warranted against defects in materials and craftsmanship for the life of the case to the original owner. That means if your case breaks, SKB will supply replacement parts, repair the case, or replace your case for as long as you own it. Proof of Purchase is required for all warranty claims. To register your case, fill out the form here.
Most latches, handles, and wheels are considered field replaceable, and can be provided at no charge to the original owner. If you need parts, contact our customer service department:
By phone: (714) 685-5207
By email: customerservice@skbcases.com
Online: Support Request form
Most repairs can be completed within two weeks of receiving your case.
Some cases can be retrofitted with TSA latches. Please contact our customer service department at (714) 685-5207 or customerservice@skbcases.com for more information.
Proudly Made in the USA
SKB iSeries Cases are molded from a proprietary blend of ultra high-strength polypropylene copolymer resin that makes them both lighter and 2.8x stronger than the competition. Every iSeries case is designed, manufactured, assembled, and finished at our factory in Orange, California—and has been since the beginning. It's this unsurpassed commitment to quality and innovation that makes SKB Cases the gold industry standard for military-grade protective cases.